H40XDT2-e
Series | Digital Module |
DI/DO points | 20DI/20DO, Transistor NPN output |
COM Port | Built-in 1*Ethernet port+1*RS485 port |
Remote I/O module | Supported |
The expansion module with Ethernet port also has all the functions of the expansion module of same type without Ethernet port, it also supports Haiwell cloud platform,can use Haiwell cloud to do remote programming for Haiwell PLC ,upload/download,firmware upgrade,self-diagnosis,monitor and debug. Easy for remote connection and monitoring the real-time data of the site. |
- Product Introduction
- Technical Specification
- File Download
Model | Power | DI | DO | Communication | Dimension |
H40XDT2-e | 220V AC | 20 | 20 Transistor NPN | RS485 | 131*95*82mm |
Terminal wiring diagram
Product DI specification
Item | Digital Input DI |
Input signal | Non-voltage contact or NPN/PNP contact |
Action driving | ON: 3.5 mA above OFF: below 1.5 mA |
Input impedance | About 4.3KΩ |
Input maximum current | 10mA |
Response time | Default 6.4ms,Configurable 0.8~51.2ms |
Isolation mode | Each Channel optical isolation |
Input indication | LED light means ON, dark means OFF |
Power supply | PLC internal power supply: DC power(sink or source)5.3mA@24VDC |
Digital input (DI) wiring diagram
Product DO specification
Item | Relay Output-R | NPN or PNP transistor output - T/P | |
maximum load | Resistance load | 2A/1 point,8A/4 point per COM | 0.5A/1 point,2A/4 point per COM |
Inductive load | 50VA | 5W/24VDC | |
Light load | 100W | 12W/24VDC | |
Min. load | 10mA | 2mA | |
Voltage specification | Below 250VAC,30VDC | 30VDC | |
Drive capability | Maximum 5A/250VAC | MAX 1A 10S | |
Response time | Off-on 10ms,On-off 5ms | Off→On 10μs, On→Off 120μs | |
Leakage current when route opened | --- | Below 0.1mA | |
Isolation mode | Mechanical isolation | Each Channel optical isolation | |
Output indication | LED light means ON , dark means OFF | ||
Power supply | PLC internal power supply 24VDC |
Digital Output (DO) wiring diagram
CR Number | Function Declare |
H40XDT2 | |
00H (Read only) | The low byte is the module code, and the high byte is the module version number. |
01H | Communication address |
02H | Communication protocols:The low 4-bit of the low bytes: 0 - N,8,2 For RTU,1 - E,8,1 For RTU, 2 - O,8,1 For RTU,3 - N,7,2 For ASCII,4 - E,7,1 For ASCII,5 - O,7,1 For ASCII,6 - N,8, 1 For RTU |
The high 4-bit of the low bytes: 0 – 2400,1 – 4800,2 – 9600,3 – 19200,4 – 38400, 5 – 57600,6 - 115200 | |
03H~06H | Extend module name |
07H~08H | Default IP address: 192.168.1.111 |
09~0AH (Read only) | Reserve |
0BH | High byte subnet mask (b3~b0,1 indicates 255, 0 indicates 0, for example, subnet mask 255.255.255.0, b3~b0=1110), low byte reserved |
0CH~0EH (Read only) | Reserve |
0FH (Read only) | Error code : 0-normal, 1-illegal firmware identity ,2-incomplete firmware, 3-system data access exception, 4-No external 24V power supply |
10H~4FH (Read only) | DI channel 1~64 input value |
50H~8FH | DO channel 1~64 output value |
90H | Filtering time of DI ms, 0 - 0.8、1 - 1.6、2 - 3.2、3 - 6.4、4 - 12.8、5 - 25.6、6 - 51.2 |
91H~9FH (Read only) | Reserve |